Shrockworks Skid hardware

[gorillamel]

I bought the Shrock transfer case skid off a member of TNX. It did not come with the hardware (nor did I expect it to). Those of you that have this skid, what hardware do you have to mount it? I know grade 8, but not sure of size and length of the bolts and stuff, and how many if different kinds.

 

[brett]

T-case Skid:
1 - 3/8”x1 1/2” bolts
3 - M8 1.25 30mm Bolts
1 - 3/8” nuts
3 - 5/16” washers
1 - 3/8” washer
3 - 5/16” lock washers
1 - 3/8” lock washer
1 - 3/8” Fender Washer

Creek put a detailed thread over on TNX years ago that even has the instructions. Just look in the archived Shrockworks forum, it's a sticky at the top.
Hope this helps!

 

[gorillamel]

Much appreciated! I should have looked there in the first place.

 

[gorillamel]

I am copying and pasting what is used on that sticky here simply b/c TNX is no longer on tapatalk, so I cannot access it on my phone when installing all this crap. http://www.thenewx.org/forum/showthread.php?t=20242

A big thanks to Kevin at Shrockworks for hooking it up

Front Radiator Skid:
4 - M12x1.25x35 Bolts
4 - ½” Washers
4 - ½” Lock Washers
2 - ¼” Flat headed bolts

Engine Skid:
2 - 3/8”x1” bolts
4 - M8 1.25 40mm Bolts
2 - 3/8” nuts
4 - 5/16” washers
4 - 3/8” washers
4 - 5/16” lock washers
2 - 3/8” lock washers
2 - ½” spacers

Transmission Skid:
2 - 3/8”x2 1/2” bolts
3 - M8 1.25 30mm Bolts
2 - 3/8” nuts
3 - 5/16” washers
2 - 3/8” washers
3 - 5/16” lock washers
2 - 3/8” lock washers
2 - 3/8” Fender Washers

T-case Skid:
1 - 3/8”x1 1/2” bolts
3 - M8 1.25 30mm Bolts
1 - 3/8” nuts
3 - 5/16” washers
1 - 3/8” washer
3 - 5/16” lock washers
1 - 3/8” lock washer
1 - 3/8” Fender Washer

Gas Tank Skid:
4 - M8 1.25 30mm Bolts
4 - 5/16” Nuts
8 - 5/16” washers
1- 3/16 Laser Cut Steel “Tab A”
8 - 5/16” lock washers
1- 3/16 Laser Cut Steel “Tab B”
4 - 5/16 Carriage Bolts

Sliders:
4 1/2" x 1 1/4" Bolt
2 1/2" x 4" Bolt
2 M10 1.25 x 30mm Bolt
10 1/2" Flat Washers
4 1/2" Nuts
4 1/2" Lock Washers
2 3/8" Flat Washer
2 M10 Lock Washers
2 Handle Nuts - 1/2" (nut with attached handle)

Front Bumper:
8 - M12x1.25x35 Bolts
6 - ½” x 1 1/2” Bolts
20 - ½” SAE Washers
14 - ½” Lock Washers
6 - ½” Nuts
6- 3/8” x1 ¼” bolts
12 - 3/8” washers
6 - 3/8” Lock Washers
6 - 3/8” Nuts
11 - ¼” x 1” Bolts
24 - ¼” Flat Washers
11 - ¼” Lock Washers
11 - ¼” Nuts
2- Frame Brackets
1 - Skid Plate
2 - Fog Light Spacers
1 - Skid Plate Bracket
1 - Winch Solenoid Mount

Rear Bumper w/ Tire Carrier:
1 - 1” x 5 7/8” Bolt
2 - 1” SAE Washers
1 - 1” Nut
1 - ½” x 2” Bolt
2 - 1” Bronze Washers
3 - ½” Nut
1 - Tire Mount
3 - ½” x 1 ¼” Bolt
2 - ½” Wing Nut
1 - Hi-Lift Base Pin
9 - ½” Flat Washers
3 - M12 1.25 Lug Nuts
2 - m12 1.25 35mm bolts
12 - ¼” Nut
1 - Latch Assembly
4 - ¼” x 1” Flathead Cap Screw
12 - ¼” x 1” Bolt
20 - ¼” Washers
16 - ¼” Lock Washers
3 - ½” Lock Washers
2 - Nylon Gate slides
1 - trailer plug mount

Diff Skid:
8 - 5/16”x1” bolts (D44 Rear End)
- OR -
6 – M10 30mm x 1.25 bolts (C200 Nissan Rear End)

I cannot open the PDF's on TNX. If anyone else is able to, can you attach them to this thread?

 

[Dephep]

Awesome, thanks for running this down. I started my skid project and they are pretty much ready to cut holes and bolt up.

 

[Dephep]

All ready to attach.

 

[gorillamel]

Oooo very nice!

 

[jaycee]

Thanks! Crawled under the truck to touch up the paint on the skids, and found a couple bolts missing. Glad I found this info.